CMS ERROR Code List 1 - "Unassigned (unallocated) number"This cause indicates that the destination requested by the Mobile Station cannot be reached because, although the number is in a valid format, That said, +CMS ERROR: 500 is often a result of low/marginal signal strength. On which physical drive is this logical drive? Why does the '!!' shortcut fail to execute the previously run command?
To adjust retry behaviour for any error (not just CMS ERROR: 500), see http://www.nowsms.com/sms-retry-error-handling-with-ucpemi-and-cimd If you still want to immediately reject any messages that return CMS ERROR: 500, this is only Now you have a S40 "smart phone" with at least 3rd edition of firmware. or is this maybe the problem? Member Registered:May 2009 Posts: 22 Location: Austria Topic owner thx keke i will look at this post... http://ozekisms.com/index.php?owpn=598
Is it in Milliseconds? Instead of just displaying the "ERROR" message, it also shows an error number. Try this: AT ok AT+csca="+ sms service number,145" ok AT+cmgf=1 ok AT+cmgw="+yourcountrycode telephon number" all together Hi (Ctrl+z) +CMGW: (u will get random number) ok AT+cmss=(your random number) +CMSS:.... Maybe u need to set your sms center service number first, then send sms.
Connect to the modem using HyperTerminal, and issue the command AT+CSQ. The latest version can be downloaded from the following website: http://www.ozekisms.com/index.php?owpn=112&viewunofficial=on 2.) Enable "slow modem communication" on the "port settings" tab of the "GSM modem configuration" form. 3.) Change the "HW GsmFavorites.com Internet resource for mobile communication software. Cms Error 321 before retrying [ Select ]phone is now connected with usb keke Top #24 Mon May 25, 2009 09:03, 91 months ago.
First, I confirm that it's not a signal issue with my case, the signal is full. Cms Error 500 Huawei Next try sending using Minicom. You can set the SMSC address by manually editing the SMSGW.INI file. We try to keep this list up to date, so please send your comments to [email protected] or post them in our forum.
That's why most advanced GSM devices support extended errors. news The syntax of this extended error is either "+CMS ERROR: xxx" or "+CME ERROR: xxx". Cms Error 500 Smscaster When you enter the SMSC phone number, always start it with a "+" and don't include any other non-numeric characters (no dashes or dots) in the address. Cms Error 305 Before 2006 it was working.
The modem does not specify due to which reason the error occurs. However it's coming soon. Administrator Registered:May 2009 Posts: 1731 Location: Jyväskylä, Finland Thank's, the weekend was nice and it looks like this newly started week is going to be interesting too... Under the [Modem - driver name] section header, add: DelayAfterSend=#### and/or DelayAfterError=#### In both cases, #### is a millisecond (1/1000 of a second, example 1000 = 1 second) delay after a Cms Error 304
WindowsToolkits.com Internet Resource for Windows toolkit software. Support Support Forums Quick Start Guide Developer APIs MMSC Training Documents MMS Protocol Overview Phone To MMSC Protocol (MM1) MMSC Interconnection Protocol (MM4) Tech Support Bulletins Tech Support Blog Software Updates before retrying [ Select ] [ Expand ]my config file:# AUTOMATICALLY CREATED CONFIGURATION FILE -- DO NOT EDIT BY HAND!## Description: Main configuration file for the smsd# Last changed: Mit Also, I want to re-emphasize the following point from my previous reply: My experience is that using a phone as a modem is not as reliable as using a dedicated modem
Member Registered:May 2009 Posts: 22 Location: Austria Topic owner thanks for the fast answeari tried it with 43676... Gsmcomm Message Service Error 500 Occurred luke Top #17 Fri May 22, 2009 10:55, 91 months ago. It has outstanding APIs for software developers.
Des - NowSMS Support Board AdministratorUsername: DesosmsPost Number: 3951Registered: 08-2008Posted on Monday, May 07, 2012 - 02:42 pm: Hi, Please re-read my previous message. With a smsd version you are using, destination number must always be written using international format (without a plus sign), Try To: 43676xxxxx and I think your message will be sent. Yes. Cms Error 21 The term "not functioning correctly" indicates that a signalling message was unable to be delivered to the remote user; e.g., a physical layer or data link layer failure at the remote
may i bother you again at monday ? Please note I tried Huwaei modem and it was working perfectly, but what could be the reason behind this failure with Soney Ericson device?! Please login or register. Join them; it only takes a minute: Sign up CMS Error 500 error when sending message using AT command up vote 0 down vote favorite I'm trying to send an SMS
When there is a network error, for instance, when you try to send an SMS message when there is no network coverage, you will receive an error which starts with "+CMS To determine if this is the problem, try going into "Properties" for the modem in the "SMSC" list of NowSMS, and change "SMS Access" to "GSM". +CMS ERROR 330 occurs frequently Is the error message same? Next page: Connection problem Copyright © 2000 - 2016 Ozeki Informatics Ltd.
no channel, facility busy/congested etc.). 22 - "Memory capacity exceeded".This cause indicates that the mobile station cannot store the incoming short message due to lack of storage capacity. Please advise. OZEKI NG SMS Gateway "The World's most reliable SMS gateway software!" [email protected] Tel.: 00 36 52 532 731 Overview Quick start Download Manual How to buy FAQ Contact Us OZEKI NG This includes almost all types of binary messages, as well as long text messages.
SMS & MMS Protocols NowSMS Features Developer APIs Mobile Operator MMSC How MMS Works What is a GSM Modem? luke Top #12 Fri May 22, 2009 09:41, 91 months ago. However, if in practice you are seeing a large number of errors that result in retries, and a forced delay reduces the number of such errors and retries, throughput is increased. Probably current firmware is broken and this device cannot be used for sending (which sounds strange, but anything is possible).You have rtscts = no, why handshaking is disabled?
Under the section header for the modem configuration (e.g., [Modem - …], add SMSC=+phonenumber, where "+phonenumber" is the address of the SMSC. There is not a global setting that applies to all modems. -- Des NowSMS Support Login / Register Logout Last 30 Days Topics Purchase NowSMS Now Supporting Android Phones as Modems If you try setting the SMSC value by manually editing SMSGW.INI … if the setting doesn't make a difference, always go back in and remove it immediately so that it doesn't Another issue that we have encountered in the past is some phone modems working more reliably if we force an idle wait period after sending attempts to give the phone software
Thanks. The question was not about sending messages, but he also did not say that sending does not work... Menu Home Basic information: Slideshow, watch this first License How to compile/install - Instructions for Windows How to configure - Configuring providers Localizing How to run/use SMS file format - User It's a useful reference that I seem to search for a few times every month, so to make the information easier to find, I figured I would post it here.