Below is the excerpt from the bb log >> >> >> 2011-06-23 19:44:04   DEBUG: re-queing SMS not-yet-to-be resent >> 2011-06-23 19:44:04   DEBUG: sms_router: handling message >> (0x9bd40d0 Below are the SMS AT commands that may output the final result code +CMS ERROR: +CMGC (command name in text: Send Command) +CMGD (command name in text: Delete Message) +CMGL (command General FAQ Ask a Question Bugs and Suggestions Article Help Forum Site Map Advertise with us About our Advertising Employment Opportunities About Us Ask a Question All Questions All Unanswered FAQ Below shows some common causes of +CMS errors: A SIM card is not present in the GSM/GPRS modem or mobile phone. check over here
It is very helpful. Unlike OK and ERROR, the +CMS ERROR final result code is only available to SMS AT commands. luke Top #12 Fri May 22, 2009 09:41, 91 months ago. Final Result Code Specific to SMS AT Commands Preferences - Do not show ads The final result codes OK and ERROR are available to all AT commands. http://stackoverflow.com/questions/24878173/cms-error-500-error-when-sending-message-using-at-command
GSM Modem #1 Regards Allan Holdt Add Reply Add Topic Add Reply: Error 500 (unknown error) when sending SMS messages Guest name (required): Guest email (required): NOTE: new posts are subject Always restart the gateway service after making a change to the SMSGW.INI file. I posted a list of CMS ERROR codes on the NowSMS discussion board almost 5 years ago at http://www.nowsms.com/discus/messages/1/829.html. What happens if BB-8 rolls the wrong way?
Events happen on both modems. It's a useful reference that I seem to search for a few times every month, so to make the information easier to find, I figured I would post it here. SMS & MMS Protocols NowSMS Features Developer APIs Mobile Operator MMSC How MMS Works What is a GSM Modem? Cms Error 500 Huawei Member Registered:May 2009 Posts: 22 Location: Austria Topic owner thx keke i will look at this post...
more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed error_code is an integer that is associated to a certain error. Next test run will be tomorrow morning. http://smstools3.kekekasvi.com/topic.php?id=47 It notifies you about the occurrence of a message service failure. 16.2.1.
If it is too high then it indicates that there are connection problems between the modem and the network. Cms Error 321 Before I get to the list, and the sometimes cryptic definitions defined in the specifications, I want to highlight a few of the error codes that seem to occur most frequently. See more: AT Hi guys i am sending SMS in GSM Modem using AT commands via Microsoft Hyper-terminal. Why are the memory addresses of string literals so different from others', on Linux?
Next try sending using Minicom. An error code is provided for programmers to check what causes the message service failure. Cms Error 500 Smscaster However, the information element is not required to be present in the message in order for the equipment sending the cause to process the message. 111 - "Protocol error, unspecified"This cause Cms 500 Error For instance, you are trying to read a phonebook entry before entering a pincode.
Introduction to SMS Messaging 2. check my blog luke Top #21 Fri May 22, 2009 13:27, 91 months ago. To determine if this is the problem, try going into "Properties" for the modem in the "SMSC" list of NowSMS, and change "SMS Access" to "GSM". +CMS ERROR 330 occurs frequently Member Registered:May 2009 Posts: 22 Location: Austria Topic owner handshake was off because of the old config (other tool) i tried it with yes and no (no difference) i also tried Cms Error 305
This file is not meant# to be and should not be editted directly.# Instead# Run: dpkg-reconfigure <-plow> smstools## If you want to manage your configuration file by hand at a later It has incorrect information. GSM Modem #1 25-11-2014 08:49:58 The GSM Modem returned +CMS ERROR: 500 (Unknown error) after the command. this content The SIM card requires a password (e.g.
It seems to be a bug in commonly used modem chipsets, where they do not read this address automatically from the SIM. Gsmcomm Message Service Error 500 Occurred The 'Message send errors' indicate the number of errors after attempting to send the messages and the 'Messages sent' indicates the number of messages that are successfully sent. Your Email This email is in use.
IMSI not known). 29 - "Facility rejected"This cause indicates that the facility requested by the Mobile Station is not supported by the PLMN. 30 - "Unknown subscriber"This cause indicates that the I have set the send delay to two seconds. The syntax of this extended error is either "+CMS ERROR: xxx" or "+CME ERROR: xxx". Cms Error 304 How to Send SMS Messages from a Computer / PC? 11.
Hence, the command line you entered, together with the response returned, will be displayed like this in a terminal program such as HyperTerminal of Microsoft Windows: AT+CMGR=11+CMS ERROR: 321 To find A 17th century colloquial term for children, in the way we use 'kids' today Why do most of us wear wristwatches on the left hand? From what we've seen, when this error occurs, it is usually the same as error 500. Member Registered:May 2009 Posts: 22 Location: Austria Topic owner hmmmm well i tried if the PUD gives me a OK back so i not realy tried to send it...
Administrator Registered:May 2009 Posts: 1731 Location: Jyväskylä, Finland The sendsms script is ok, even when it's old and there is a better version available.You smsd also is very old, it could It can be used for: Phone calls from SQL Phone calls from HTTP Voice and SMS applications Callcenter developers If you are working on telephone solutions, please check out the Ozeki luke Top #15 Fri May 22, 2009 10:35, 91 months ago. When you enter the SMSC phone number, always start it with a "+" and don't include any other non-numeric characters (no dashes or dots) in the address.
GSM Modem #1 25-11-2014 08:49:58 Serial port closed. Member Registered:May 2009 Posts: 22 Location: Austria Topic owner thanks for the fast answeari tried it with 43676... Sending SMS Messages from a Computer / PC Using AT Commands (AT+CMGS, AT+CMSS) 26. Member Registered:May 2009 Posts: 22 Location: Austria Topic owner and heres the command i'm using trying to send sms: [email protected]:~# /usr/local/bin/sendsms Destination: 43676xxxxxxx Text: Test [ Select ]maybe just my command
Administrator Registered:May 2009 Posts: 1731 Location: Jyväskylä, Finland ^Z is a PDU termination character and it should be there.Perhaps you could try without smsc setting, in most cases this setting is When the error starts with "+CME ERROR", it means that the error is a device specific error code. There is no resolution for this problem, other than to use a different modem that does not suffer from this bug. +CMS ERROR 512 is defined as a manufacturer specific error. It is not unusual that the error 'CMS ERROR: 500' is returned once in a while but when this does not happen too much it is not a problem.