Home > Cms Error > Cms Error 500 Kannel

Cms Error 500 Kannel

Finally you should add sim-buffering in order to make kannel read and delete messages in modem; either in equipment or sim Regard Alvaro |-| EnvĂ­e y Reciba Datos y mensajes de If it receices an SMS it sends it to a default mail address. After each try modem is being disconnected and connects again. Thank you for your help.

keke Top #14 Fri May 22, 2009 10:27, 91 months ago. Faq Reply With Quote Share This Thread  Tweet This + 1 this Post To Linkedin Subscribe to this Thread  Subscribe to This Thread « Previous Thread | Next Thread luke Top #12 Fri May 22, 2009 09:41, 91 months ago. We also found that in Linux, our 3G Huawei key appears 2 times: ttyUSB1 and ttyUSB2. http://www.kannel.org/pipermail/users/2011-June/015985.html

Zaharia Constantin Re: Kannel and one phone number produce 500 co... Hope helps. number through minicom: AT+CMGL="all" and got a list of received SMS-s. If the problem happens occasionally, you can configure multiple retries for message delivery on the "Advanced" tab of the "Edit/server preferences" form by setting the value of the "Max number of

I'll have a look at it. (500) DETAIL DATA 2008-10-26 19:48:27 [13460] [6] INFO: AT2[bmc]: Phase 2+ is supported 2008-10-26 19:48:27 [13460] [6] DEBUG: AT2[bmc]: -- AT+CSMS=1^M 2008-10-26 19:48:27 [13460] [6] Well, I very knew for me Kannel, sms sending ... We use Kannel only for shipments of SMS via HTTP. Knut Olafson Re: Kannel and one phone number produce 50...

But, if it is treated as bug it would be > resolved by now.... Best regards. Clear did not helped. http://kannel.6189.n7.nabble.com/CMS-ERROR-CMS-ERROR-500-and-Generic-error-ERROR-td10397.html Please note that the bearer-box is an up-to-date CVS version.

This error can happen if: The phone number you try to send your message to is invalid There is no network coverage You don't have enough money on a prepaid subscription A SIM card from a different network in the same modem will send OK. Probably current firmware is broken and this device cannot be used for sending (which sounds strange, but anything is possible).You have rtscts = no, why handshaking is disabled? It is better to have it separate for each smsc.

Usually it only stores outgoing until confirmed by smsc that it has received then is automatically deleted. Visit Website You should check which tty correspond to the AT command port. sms not being sent "+CMS ERROR: +CMS ERROR: 500 " Rene Kluwen rene.kluwen at chimit.nl Thu Jun 23 17:41:28 CEST 2011 Previous message: sms not being sent "+CMS ERROR: +CMS ERROR: No reception.

GoldStar CMS takes telematics to the next level, with a host of GPS vehicle …… Non-partisan research and policy institute working on federal and state fiscal policies and public programs that bearerbox being unable to communicate with the modem could be caused by modem memory being full. Philippe. -Original Message- From: Alvaro Cornejo [email protected] [mailto:[email protected]] To: Equipe Support [email protected] [mailto:[email protected]] Cc: kannel_dev_mailinglist [email protected] [mailto:[email protected]], [email protected] [mailto:[email protected]], users [email protected] [mailto:[email protected]] Date: Thu, 14 May 2015 10:27:30 -0500 Subject: Re: Next page: Connection problem Copyright © 2000 - 2016 Ozeki Informatics Ltd.

You can use value between 2 and 5.# alarmlevel = 4#eventhandler = /usr/local/bin/sendsms#blacklist = /etc/smstools/blacklist#whitelist = /etc/smstools/whitelist#autosplit = 3loglevel = 7# Modem configuration[6310i]device = /dev/ttyS0incoming = yesmode = newsmsc = 43664xxxxxxxrtscts First we stopped and restarted kannel. I therefore recommend to compile from sources anyway.You have used this SIM and phone to send similar SMS and it has worked, right?luke wrotei checked the commands with minicom and they Was there some troubles with receiving messages when handshaking was on?Perhaps you could make one more try with Minicom and ASCII mode, give a number in national format, AT+CMGS="0676xxxxx".

The solution we found for now: stop Kannel services, change the modem in minicomwith ttyUSB1 or ttyUSB2, modify kannel.conf (with ttyUSBxx modem) and restart bearebox and SMSBOX. We use Kannel only for shipments of SMS via HTTP. I'll have a look at it. (500) Thank you for helping us. -- Best regards Tomasz Re: Invalid recipient number CMS ERROR: 500 requeuing such messages 2010-05-10 Thread Alvaro Cornejo Add

However it's coming soon.

Waiting for your reply. Member Registered:May 2009 Posts: 22 Location: Austria Topic owner hmmmm well i tried if the PUD gives me a OK back so i not realy tried to send it... Or maybe there is some other solution to disallow queuing messages sent to invalid number? We also found that in Linux, our 3G Huawei key appears 2 times: ttyUSB1 and ttyUSB2.

I've found a simple way to reset the module by: echo -ne AT+CFUN=1,1\r /dev/ttyUSB1 and within a script I tried: CMS=`tail -n10 /var/log/kannel/smsc.log | grep 'ERROR'` if [ x$CMS != x Otherwise it won't send any SMS anymore. Seems to mean that the SIM card rejected the message. bearerbox being unable to communicate with the modem could be caused by modem memory being full.

Member Registered:May 2009 Posts: 22 Location: Austria Topic owner Version 3.0.10, Copyright (c) Keijo Kasvi, authors email, http://smstools3.kekekasvi.comBased on SMS Server Tools 2 from Stefan Frings, email of version 2 author,