Home > Cms Error > Cms Error 330

Cms Error 330

Contents

Unlike OK and ERROR, the +CMS ERROR final result code is only available to SMS AT commands. Under the section header for the modem configuration (e.g., [Modem - …], add SMSC=+phonenumber, where "+phonenumber" is the address of the SMSC. CMS ERROR 22 "Congestion". The SMSC address is unknown or incorrect.

Hence, when an error occurs, you will not find both +CMS ERROR and ERROR in the command response. CMS ERROR 27 "Destination out of service" This cause indicates that the destination indicated by the Mobile Station cannot be reached because the interface to the destination is not functioning correctly. Introduction to SMS Messaging 2. Always restart the gateway service after making a change to the SMSGW.INI file. https://www.nowsms.com/gsm-modem-cms-error-code-list

Cms Error 304

To resolve this error, you need to manually define the operator SMSC address in the NowSMS configuration. CMS ERROR 17 "Network failure". The syntax of this extended error is either "+CMS ERROR: xxx" or "+CME ERROR: xxx". CMS ERROR 8 "Operator determined barring" This cause indicates that the MS has tried to send a mobile originating short message when the MS's network operator or service provider has forbidden

If it works, check what is the correct number of SMSC.Btw: Why you have disabled pre_init and use init = ATZ? manufacturer specific Dig deeper! All rights reserved Software PBX for Windows | VoIP SDK | Legal information | Privacy policy | Terms of use Please, address your inquiries to [email protected] CompHelp - Menu Skip to Cms Error Codes It has broken links.

Under the section header for the modem configuration (e.g., [Modem - ...], add SMSC=+phonenumber, where "+phonenumber" is the address of the SMSC. Cms Error 500 Smscaster Thus, if the command line sent to Nokia 6021 is "AT+CMGR=11;+CGMI" (+CGMI is the AT command for retrieving the manufacturer name of the GSM/GPRS modem or mobile phone), you will get You can set the SMSC address by manually editing the SMSGW.INI file. https://groups.google.com/d/topic/smslib/KgsFr7gJucI General Syntax of Extended AT Commands 16.

CMS ERROR 128 Telematic interworking not supported x CMS ERROR 129 Short message Type 0 not supported x x CMS ERROR 130 Cannot replace short message x x CMS ERROR 143 Cms Error 512 Wavecom IMSI not known). Even if the GSM modem has been detected, the SMS is not being sent. If you try setting the SMSC value by manually editing SMSGW.INI … if the setting doesn't make a difference, always go back in and remove it immediately so that it doesn't

Cms Error 500 Smscaster

WindowsToolkits.com Internet Resource for Windows toolkit software. http://www.ozekisms.com/index.php?ow_page_number=380 IMSI not known). 29 - "Facility rejected"This cause indicates that the facility requested by the Mobile Station is not supported by the PLMN. 30 - "Unknown subscriber"This cause indicates that the Cms Error 304 SMS & MMS Protocols NowSMS Features Developer APIs Mobile Operator MMSC How MMS Works What is a GSM Modem? Cms Error 38 Below is the result displayed in Windows' HyperTerminal: AT+CGMI;+CMGR=11Nokia+CMS ERROR: 321 16.2.1.1.

Final Result Code Specific to SMS AT Commands Preferences - Do not show ads The final result codes OK and ERROR are available to all AT commands. Your cache administrator is webmaster. E-mail: [email protected] If you have a technical question, please submit a support request on-line. Inter-operator SMS Messages 8. Cms Error 305

Any help would be greately appreciated! Remove the SIM card from the modem, and put it into a mobile phone. CMS ERROR 28 "Unidentified subscriber" This cause indicates that the subscriber is not registered in the PLMN (i.e. It is not helpful.

This error can be completely ignored._________________Tech Support [email protected] http://www.notepage.net Back to top Display posts from previous: All Posts1 Day7 Days2 Weeks1 Month3 Months6 Months1 YearOldest FirstNewest First NotePage, Inc. Invalid Pdu Mode Parameter Preferences - Do not show ads Page 23 of 65 Previous Page | Next Page Table of Contents Contents at a Glance 1. CMS ERROR 38 "Network out of order" This cause indicates that the network is not functioning correctly and that the condition is likely to last a relatively long period of time;

if the setting doesn't make a difference, always go back in and remove it immediately so that it doesn't confuse things down the road. 3.) If #1 doesn't work, try this:

Below shows some common causes of +CMS errors: A SIM card is not present in the GSM/GPRS modem or mobile phone. The +CMS ERROR Final Result Code -- Notifies the Occurrences and Causes of Message Service Failures The +CMS ERROR final result code is returned when a message service failure occurs. Setting or Reading the Service Center Address / SMSC Address (AT+CSCA) 22. What Is Sms Text Mode And Pdu Sms Mode? Intra-operator SMS Messages 7.

How to Use Microsoft HyperTerminal to Send AT Commands to a Mobile Phone or GSM/GPRS Modem? 14. The term "not functioning correctly" indicates that a signaling message was unable to be delivered to the remote user; e.g., a physical layer or data link layer failure at the remote In the "SMSC" list, highlight the modem and press "Properties". Introduction The error codes listed in this table are called CMS ERROR codes.

If you cannot, then there may be a problem with your account with the mobile operator. (Note: We have observed that with some mobile operators, if you buy a modem with Toshiba doesn't make a lot of GSM phones, so I wouldn't be surprised if their GSM modem interface was a bit untested.